欢迎访问《金属矿山》杂志官方网站,今天是 分享到:
×

扫码分享

金属矿山 ›› 2026, Vol. 55 ›› Issue (10): 81-92.

• • 上一篇    下一篇

考虑采充时序的深部阶段胶结充填体强度计算方法

卢宏建1,2 ,任兆阳1 ,夏传祥3 ,路燕泽4 ,荣 辉4 ,刘志义1,2   

  1. 1.华北理工大学矿业工程学院,河北 唐山 063210;2.河北省矿山绿色智能开采技术创新中心,河北 唐山 063210; 3.山东金岭矿业股份有限公司,山东 淄博 255000;4.河北钢铁集团矿业有限公司,河北 唐山 066501
  • 出版日期:2026-11-03 发布日期:2026-11-09
  • 作者简介:卢宏建(1980—),男,教授,博士,博士研究生导师。
  • 基金资助:
    国家自然科学基金项目(编号:52574145);河北省中央引导地方科技发展资金项目(编号:246Z4101G)。

Strength Calculation Method for Deep Stage Cemented Backfill Considering the Mining and Backfilling Sequences

LU Hongjian1,2 ,REN Zhaoyang1 ,XIA Chuanxiang3 ,LU Yanze4 ,RONG Hui4 ,LIU Zhiyi1,2   

  1. 1.Shool of Mine Engineering,North China University of Science and Technology,Tangshan 063210,China; 2.Green Intelligent Mining Technology Innovation Center of Hebei Province,Tangshan 063210,China; 3.Shandong Jinling Mining Industry Co.,Ltd.,Zibo 255000,China;4.HBIS Minging Co.,Ltd.,Tangshan 066501,China
  • Online:2026-11-03 Published:2026-11-09

摘要: 考虑采充扰动应力环境,是深部金属矿阶段空场嗣后充填开采强度设计不可忽略因素。基于MIDAS GTS、Matlab软件平台与尖点突变理论,提出了一种考虑采充时序的深部阶段胶结充填体强度计算方法,可获取胶结 充填体破裂面、破坏区域体积与整体安全系数定量评价指标。首先,选取优化目标矿山,构建矿体开采与充填采充时 序过程的三维数值计算模型;然后,依据强度折减法对黏聚力和内摩擦角参数折减后的数值计算结果,构建典型测点 总位移与折减系数的尖点突变模型函数,确定胶结充填体失稳总位移阈值和对应的安全系数阈值;最后,运用柱网离 散法,重构含位移与应力信息的胶结充填体强度需求Matlab三维分析模型,依据总位移与安全系数阈值计算胶结充 填体破裂面、破坏区域体积、破裂面整体安全系数,确定胶结充填体需求强度,对比案例计算结果与文献数据验证了 模型可信度。研究结果对深部阶段空场嗣后充填开采胶结充填体强度需求计算具有理论指导和工程应用价值。

关键词: 金属矿山 , 深部开采 , 胶结充填体 , 采充扰动 , 强度需求计算

Abstract: In the strength design of cemented backfill for deep stage open stoping with subsequent backfill mining,the disturbance caused by mining activities and variations in the backfill stress environment is a critical factor that cannot be over looked.Based on the MIDAS-GTS and Matlab software platforms,along with the cusp catastrophe theory,a method for calculat ing the strength of deep-stage cemented backfill was proposed,taking into account the sequence of excavation and backfilling. This method enables quantitative evaluation of the failure surface,the volume of the damaged zone,and the overall safety factor of the cemented backfill.First,a target mine was selected for the case study,and a three-dimensional numerical model was es tablished according to the actual sequence of orebody excavation and backfilling.Then,the numerical model calculation results of the reduced cohesion and internal friction angle parameters were obtained through the strength reduction method.A cusp ca tastrophe model function was constructed to relate the total displacement at typical monitoring points to the strength reduction factor.Based on this model,the critical total displacement indicating instability of the cemented backfill was identified,and the corresponding threshold safety factor was determined.Subsequently,a three-dimensional analysis model incorporating displace ment and stress information was reconstructed in Matlab using a column-grid discretization approach.Based on the thresholds of total displacement and safety factor,the failure surface,the volume of the damaged zone,and the overall safety factor of the ce mented backfill were computed,leading to the determination of the required strength for the backfill material.The reliability of the proposed model was verified by comparing the case study results with data from existing literature.The research results pro vide theoretical guidance and practical engineering value for determining the strength requirements of cemented backfill in deep stage open stoping with subsequent backfill mining.

Key words: metalmine,deepmining,cementedbackfill,mining-backfilldisturbance,strengthrequirement calculation

中图分类号: