欢迎访问《金属矿山》杂志官方网站,今天是 分享到:
×

扫码分享

金属矿山 ›› 2026, Vol. 55 ›› Issue (10): 93-104.

• • 上一篇    下一篇

橡胶掺量对胶结尾砂充填体力学与微观结构的影响

郭进平1 ,施金昌1 ,张 超1 ,陈 阳2 ,王小林1 ,王 鑫3   

  1. 1.西安建筑科技大学资源工程学院,陕西 西安 710055;2.陕西煎茶铃镍业有限公司,陕西 汉中 724300; 3.山阳秦鼎矿业有限责任公司,陕西 商洛 726100
  • 出版日期:2026-11-03 发布日期:2026-11-09
  • 通讯作者: 张 超(1995—),男,准聘副教授,硕士研究生导师。
  • 作者简介:郭进平(1970—),男,副教授,硕士研究生导师。
  • 基金资助:
    国家自然科学基金项目(编号:52504142);陕西省重点研发计划项目(编号:2025SF-YBXM-535);陕西省自然科学基金项目(编号: 2024JC-YBQN-0507);国家资助博士后研究人员计划项目(编号:GZC20232063);陕西省博士后科研项目(编号:2023BSHYDZZ142);陕 西省创新能力支撑计划项目(编号:2023-CX-TD-12)。

Effect of Rubber Content on Mechanical Properties and Microstructure of Cemented Backfil

GUO Jinping1 ,SHI Jinchang1 ,ZHANG Chao1 ,CHEN Yang2 ,WANG Xiaolin1 ,WANG Xin3   

  1. 1.School of Resources Engineering,Xi′an University of Architecture and Technology,Xi′an 710055,China;2.Shaanxi Jianchaling Nickel Industry Co.,Ltd.,Hanzhong 724300,China;3.Shanyang Qinding Mining Co.,Ltd.,Shangluo 726100,China
  • Online:2026-11-03 Published:2026-11-09

摘要: 为探究废旧橡胶颗粒掺量对胶结尾砂充填体力学性能与微观结构的影响,采用20目废旧橡胶颗粒等质 量替代充填体中的固体颗粒。设置0%、3%、6%、9%共4种橡胶颗粒掺量,开展单轴压缩试验与扫描电镜测试,并结 合Image-J软件对微观图像进行灰度值与孔隙率定量分析。研究表明,随着橡胶掺量增加,抗压强度呈现先降后升再 降的变化规律。橡胶掺量为6%时,橡胶与尾砂形成最优级配,颗粒堆积密实度显著提升,促使基体区域水化产物充 分生成与均匀分布,整体结构致密性大幅提高,强度与密度同步达到峰值。而在3%掺量下橡胶颗粒分散稀疏且橡胶 颗粒憎水表面局部抑制水泥水化,在9%掺量下过量橡胶颗粒发生团聚使得级配连续性破坏,均导致充填体强度降 低。微观定量分析进一步证实,6%掺量下灰度值最高、孔隙率最低,基体水化程度显著优于其他组别。研究结果为废 旧橡胶在矿山充填中的资源化利用提供参考。

关键词: 橡胶—尾砂充填体 , 力学性能 , 单轴压缩试验 , SEM分析 , 界面过渡区

Abstract: To investigate the effect of waste rubber particle content on the mechanical properties and microstructure of ce mented tailings backfill,20-mesh waste rubber particles were used to replace solid particles in the backfill by equal mass.Four dosage levels (0%,3%,6%,and 9%) were set,and uniaxial compression tests and scanning electron microscopy (SEM) tests were carried out.Quantitative analyses of grayscale values and porosity of micrographs were performed using Image-J software. The results show that with the increase in rubber content,the compressive strength exhibits a trend of decreasing first,then in creasing,and finally decreasing again.At a rubber content of 6%,an optimal gradation is formed between rubber and tailings, which significantly improves the compactness of particle accumulation.This promotes the sufficient generation and uniform dis tribution of hydration products in the matrix region,greatly enhances the compactness of the overall structure,and enables the strength and density to reach their peak values synchronously.At 3% rubber content,rubber particles are sparsely dispersed, and the hydrophobic surface of rubber locally inhibits cement hydration.At 9% rubber content,excessive rubber particles ag glomerate and disrupt the gradation continuity,both of which lead to the reduction of backfill strength.Microscopic quantitative analysis further confirms that the grayscale value is the highest and the porosity is the lowest at 6% rubber content,and the ma trix hydration degree is significantly better than that of other groups.The research results provide a reference for the resource u tilization of waste rubber in mine backfilling.

Key words: rubber-cemented tailings backfill,mechanical properties,uniaxial compression test,SEM analysis,interfacial transition zone

中图分类号: