欢迎访问《金属矿山》杂志官方网站,今天是 分享到:
×

扫码分享

金属矿山 ›› 2026, Vol. 55 ›› Issue (10): 221-230.

• • 上一篇    下一篇

基于离散元的工业磨机钢球与钢段磨矿对比研究

姚佳民1 ,刘海婵1 ,周 强1,2 ,赵环帅3 ,郭 庆1 ,常秋香1 ,赵国锋4 ,宫三朋4 ,王国强2   

  1. 1.宁波大学科学技术学院机械工程与自动化学院,浙江 宁波 315300;2.矿物加工科学与技术全国重点实验室,北京 102628; 3.河北省智能装备数字化设计及过程仿真重点实验室,河北 唐山 063000; 4.河南理工大学机械与动力工程学院,河南 焦作 454003
  • 出版日期:2026-11-03 发布日期:2026-11-09
  • 通讯作者: 周 强(1991—),男,副教授,博士,硕士研究生导师。
  • 作者简介:姚佳民(2001—),男,硕士研究生。
  • 基金资助:
    国家自然科学基金项目(编号:52304290);浙江省自然科学基金项目(编号:ZCLMS25E0401);矿物加工科学与技术全国重点实验室开 放研究基金项目(编号:BGRIMM-KJSKL-2026-29);河北省教育厅科学研究项目(编号:ZC2026264);唐山学院博士创新项目(编号: XJ2025002102)。

Comparative Study on Steel Ball and Cylpebs Grinding in Industrial Mill Based on Discrete Element Method

YAO Jiamin1 ,LIU Haichan1 ,ZHOU Qiang1,2 ,ZHAO Huanshuai3 ,GUO Qing1 ,CHANG Qiuxiang1 ,ZHAO Guofeng4 GONG Sanpeng4 ,WANG Guoqiang2   

  1. 1.School of Mechanical Engineering and Automation,College of Science and Technology,Ningbo University,Ningbo 315300,China; 2.State Key Laboratory of Mineral Processing,Beijing 102628,China; 3.Key Lab of Intelligent Equipment Digital Design and Process Simulation,Hebei Province,Tangshan 063000,China; 4.School of Mechanical and Power Engineering,Henan Polytechnic University,Jiaozuo 454003,China
  • Online:2026-11-03 Published:2026-11-09

摘要: 磨矿介质形状影响介质与矿物的作用方式,进而决定磨矿效率与产品特性。现有研究多集中于中小型 磨机,工业尺度条件下磨矿介质形状对磨机工况的影响尚缺乏系统研究。针对钢球易导致过粉碎的问题,本文提出 两种钢段替代钢球的方案(等有效表面积替换与等质量替换)。基于离散元法建立钢段多面体模型,通过小型筒磨机 试验验证功率预测的平均相对误差小于5%;在此基础上构建ϕ4.7 m工业尺度筒磨机数值模型,对比分析不同替换 方案下的磨矿介质动力学特性。结果表明:与钢球相比,钢段运动的肩部与趾部位置更高,抛落运动更为显著;在等有 效表面积替换与等质量替换条件下,钢段工况下的磨机功耗较钢球提高约5.8%。进一步研究发现,在等有效表面积 替换条件下,将钢段总质量降低约15%(即约为钢球总质量的85%),可在保持与钢球相当功耗水平的同时改善介质 受力特征,并表现出降低过粉碎倾向的潜力。研究结果可为工业应用中钢段介质的尺寸选择与级配优化提供参考。

关键词: 工业尺度筒磨机 , 离散元法 , 磨矿介质形状 , 钢段 , 过粉碎

Abstract: The shape of grinding media affects the interaction mode between media and minerals,thereby determining the grinding efficiency and product characteristics.Existing studies have mainly focused on small- and medium-scale mills,while the influence of media shape on mill performance under industrial-scale conditions remains insufficiently investigated.To ad dress the problem of over-grinding caused by steel balls,this study proposes two schemes for replacing steel balls with cylpebs: equivalent effective surface area replacement and equal-mass replacement.A polyhedral model of cylpebs was established using the discrete element method (DEM),and the average relative error of power prediction was verified to be less than 5% through laboratory tumbling mill tests.Based on this,a numerical model of a ϕ4.7 m industrial-scale tumbling mill was constructed to compare and analyze the dynamic characteristics of grinding media under different replacement schemes.The results show that compared with steel balls,cylpebs exhibit higher shoulder and toe positions,leading to more pronounced cataracting motion. Under both the equivalent effective surface area and equal-mass replacement conditions,the mill power consumption with cylpebs increases by approximately 5.8% relative to that with steel balls.Further investigation reveals that under the equivalent effective surface area replacement condition,reducing the total mass of cylpebs by about 15% (i.e.,approximately 85% of the total mass of steel balls) can maintain a power consumption level comparable to that of steel balls while improving the contact force characteristics of the media and showing potential for mitigating over-grinding.The findings provide a reference for the sizeselectionandgradationoptimizationof cylpebs inindustrial applications.

中图分类号: